Replace your defective, too short, or low-quality turntable cables with Audtek premium 1,8m dual shielded patch cable. This cable has an attached ground wire which older magnetic cartridge turntables must have. Gold plated RCA connectors with metal shell and oxygen-free copper stranded center conductor give it a professional look and delivers second-to-none performance.
Highlights
Audtek DMCG6 Premium Dual RCA Turntable Cable with External Ground Wire 180cm
Most turntable manufacturers throw in a short 3 ft., cheaply built cable to quickly hookup your turntable to an amplifier/receiver. These cables have a hard time reaching the rest of your components in a home theater or stereo rack. If the cable does reach, you might experience a humming sound or outside interference with its partially braided shielded wire. Audtek Electronic's premium 6 ft. dual shielded cable design with professional looking metal shells prevents this from happening, plus is long enough for most installs. Use the attached ground wire to prevent noise when hooking up a magnetic cartridge turntable into the phono jack on an amplifier/receiver.
Audtek's 24 AWG Oxygen-Free Copper (OFC) stranded center conductor and gold-plated connectors increase the signal strength over those super-thin thrown in cables. Patch cables that come with most turntables have very thin 30 to 32 AWG center conductors. Manufacturers save even more money by using Copper Covered Aluminum (CCA) strands that decrease your signal strength even more than thin gauge conductors. CCA strands also cause weak solder joints which leads to disconnects from the connector. Tin platted connectors over time corrode which also causes a disconnect from your amplifier/receiver. Audtek plates its connectors with gold to prevent this from happening. Audtek designs its turntable cable to deliver a clean, long-lasting signal providing enjoyable music for years to come.
Toon meer
Home audio 
Audio componenten 
Crossover componenten 
Test- & meetapparatuur 
DIY kits 
Accessoires 
Nieuwe producten 
Speakers
Versterkers
DAC converters
DSP modules
Draaitafels
Streamers
Woofers
Tweeters
Exciters
Bass shakers
Plaatversterkers
Versterker modules
Single board computers
Geassembleerde crossovers
Printed Circuit Boards (PCB)
Condensatoren
Weerstanden
Spoelen
Circuit Breakers
Crossover tools
Kroonsteen
Akoestische metingen
Elektrische metingen
Geluidsniveaumeters
DIY versterker kits
DIY component packs
DIY speaker kit
DIY subwoofer kits
DIY bluetooth speakers
DIY elektronische kits
Binding posts
Kabinet Hardware
Kabels
Connectors
Luidsprekerkasten
Elektromechaniek
Voedingen
Luidspreker reparatie
Werkplaats & Gereedschap
Versterkeraccessoires
Standaarden & beugels
Cadeaubon
Boeken
Nieuwe producten
Speakers
Versterkers
DAC converters
DSP modules
Draaitafels
Streamers
Woofers
Tweeters
Exciters
Bass shakers
Plaatversterkers
Versterker modules
Single board computers
Geassembleerde crossovers
Printed Circuit Boards (PCB)
Condensatoren
Weerstanden
Spoelen
Circuit Breakers
Crossover tools
Kroonsteen
Akoestische metingen
Elektrische metingen
Geluidsniveaumeters
DIY versterker kits
DIY component packs
DIY speaker kit
DIY subwoofer kits
DIY bluetooth speakers
DIY elektronische kits
Binding posts
Kabinet Hardware
Kabels
Connectors
Luidsprekerkasten
Elektromechaniek
Voedingen
Luidspreker reparatie
Werkplaats & Gereedschap
Versterkeraccessoires
Standaarden & beugels
Cadeaubon
Boeken
Nieuwe producten
